Ender 3 V3 SE 3D Printer, 250mm/s CR Touch Auto Leveling FDM 3D Printer with Sprite Direct Extruder, Dual Z-axis & Y-axis, Auto-Load Filament, Print Size 8.66x8.66x9.84 inch

About this item

🤗 𝐄𝐀𝐒𝐘 𝐓𝐎 𝐆𝐄𝐓 𝐒𝐓𝐀𝐑𝐓𝐄𝐃 - Creality Ender 3 V3 SE 3D printer is easy to put together in 3 steps. It uses CR Touch sensor for auto leveling and a strain sensor for auto Z offset, saving the need for a calibration card or knob screws. So easy to achieve a perfect first layer. Also, you can load or unload the filament with one tap. All set within just 20 minutes.
🤗 𝐒𝐏𝐑𝐈𝐓𝐄 𝐄𝐗𝐓𝐑𝐔𝐃𝐄𝐑 & 𝟑𝟐-𝐁𝐈𝐓 𝐌𝐀𝐈𝐍𝐁𝐎𝐀𝐑𝐃 - The market-proven “Sprite” direct drive extruder of Ender 3 V3 SE 3D printer ensures smooth and consistent feeding of PLA, PETG, and also flexible TPU, bringing more possibilities. The 32-bit silent mainboard uses an advanced stepper motor drive to control all axes more precisely for less operation noise.
🤗 𝐑𝐀𝐏𝐈𝐃 & 𝐋𝐈𝐕𝐄𝐋𝐘 𝐏𝐑𝐈𝐍𝐓𝐈𝐍𝐆 - Ender 3 V3 SE 3D printer can print at up to 250mm/s speed with 2500mm/s² acceleration, allowing you to complete the models efficiently. The Optimized UI uses motion graphics to display the leveling process and other parameters, so you will know how the printer is doing at a glance.
🤗 𝐘-𝐀𝐗𝐈𝐒 𝐋𝐈𝐍𝐄𝐀𝐑 𝐒𝐇𝐀𝐅𝐓𝐒 & 𝐃𝐔𝐀𝐋 𝐙-𝐀𝐗𝐈𝐒 - The rigid dual Z-axis lead screws reduce Z wobbling effectively. The Y-axis features two 8mm linear shafts made of strong and wear-proof steel, which underpins a steady and accurate motion of the build platform for a lasting time.
🤗 𝐄𝐀𝐒𝐘 𝐌𝐎𝐃𝐄𝐋 𝐑𝐄𝐌𝐎𝐕𝐀𝐋 𝐀𝐍𝐃 𝐌𝐎𝐑𝐄 - Ender 3 V3 SE 3D printer takes up less space but brings an ample build volume. The PC spring steel build plate is sticky and flexible, making it easy to remove the printed models by bending it slightly. Thanks to the power loss recovery function, it can resume printing after an unexpected power failure, avoiding filament and time waste.
Note： If you have problems with leveling, please check the following or contact us directly for help! First layer printing non-stick/laminated Overall non-stick/laminated: a. Clean the platform board, preheat the nozzle in advance, take out the consumables, clean the nozzle, and re-level it. b. You can apply solid glue on the platform plate before printing. c. Adjust Z-axis compensation according to the printing conditions of the first layer.